贝克曼CX4生化分析仪的错误信息（下）

admin

                    

                    

                    
                    
                    <section data-role="outer" label="Powered by gulangu"><section><p><p><img src="image/20200927/88e0c3596a0d1224091ce1d23df73078_1.png" /></p></p><p><p><img src="image/20200927/57b5f5cd544d97ccb6ae3dc100022e53_2.jpg" /></p></p><p><br  /></p></section><section data-author="gulangu"><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">37. MOTION ERROR：REAGENT MIXER SPIN</p></section></section></section><p><span><strong><span>运动错误：试剂搅拌针旋转错误</span></strong></span><br  /></p><p><span>a)检查搅拌子是否运动自由，连接是否正常。<br  />b)执行“REAGENT MIXER ALIGNMENT”诊断调节(3.6.3)。<br  />c)请联系当地维修站。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">38. MOTION ERROR：REAGENT MIXER UP/DOWN</p></section></section></section><p><span><strong><span>运动错误：试剂搅拌针上下运动错误</span></strong></span><br  /></p><p><span>a)按“HOME”检查试剂搅拌针运动情况。<br  />b)检查搅拌臂外盖，轴，传动带等是否有摩擦阻力，连接是否正常。<br  />c)检查光电传感器是否正常。<br  />d)执行“REAGENT MIXER ALIGNMENT”诊断调节(3.6.3)。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">39. MOTION ERROR：REAGENT PROBE AIR STRIP</p></section></section></section><p><span><strong><span>运动错误：试剂针气体冲洗错误</span></strong></span><br  /></p><p><span>a)检查4A电磁阀是否正常。<br  />b)执行“PROBE AIR STRIP TEST”诊断测试(3.8.3)。<br  />d)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">40. MOTION ERROR：REAGENT PROBE ROTATE</p></section></section></section><p><span><strong><span>运动错误：试剂针左右运动错误</span></strong></span><br  /></p><p><span>a)按“HOME”检查试剂针运动情况。<br  />b)检查试剂臂外盖，轴，传动带等是否有摩擦阻力，连接是否正常。<br  />c)检查光电传感器是否正常。<br  />d)执行“REAGENT PROBE ROTATE ALIGNMENT”诊断调节(3.6.2)。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">41. MOTION ERROR：REAGENT PROBE UP/DOWN</p></section></section></section><p><span><strong><span>运动错误：试剂针上下运动错误</span></strong></span><br  /></p><p><span>处理与#40同。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">42. MOTION ERROR：REAGENT PROBE WASH</p></section></section></section><p><span><strong><span>运动错误：试剂针冲洗错误</span></strong></span><br  /></p><p><span>a)执行冲洗功能冲洗试剂针内外部，观察冲洗情况。<br  />b)执行“INTERNAL PROBE/SCRUB BUBBLE TEST”诊断测试(3.8.2)。<br  />c)检查8L电磁阀和气泡发生器(BUBBLE GENERATOR)。<br  />d)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">43. MOTION ERROR：REAGENT PUMP</p></section></section></section><p><span><strong><span>运动错误：试剂注射器泵运动错误</span></strong></span><br  /></p><p><span>a)检查注射器内芯连接是否良好。<br  />b)检查注射器齿轮轴是否无润滑油。<br  />c)按“HOME”复位，观察运动情况。<br  />d)执行“REAGENT SYRINGE ALIGNMENT”诊断调节(3.6)。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">44. MOTION ERROR：REAGENT VALVE</p></section></section></section><p><span><strong><span>运动错误：试剂注射器阀运动错误</span></strong></span><br  /></p><p><span>a)检查注射器阀工作是否正常，光电传感器连接是否良好。<br  />b)冲洗试剂针内部，观察工作情况。<br  />c)执行“REAGENT SYRINGE”诊断(3.8.2.4)。<br  />d)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">45. MOTION ERROR：SAMPLE CAROUSEL</p></section></section></section><p><span><strong><span>运动错误：样品盘旋转错误</span></strong></span><br  /></p><p><span>参考#28处理。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">46. MOTION ERROR：SAMPLE MIXER ROTATE</p></section></section></section><p><span><strong><span>运动错误：样品搅拌器左右移动错误</span></strong></span><br  /></p><p><span>a)检查试剂臂外盖，轴，传动带等是否磨损阻力大。<br  />b)检查连接是否良好。<br  />c)按“HOME”复位，观察运动情况。<br  />d)执行“SAMPLE MIXER ALIGNMENT”诊断调节(3.5.3)。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">47. MOTION ERROR：SAMPLE MIXER SPIN</p></section></section></section><p><span><strong><span>运动错误：样品搅拌器旋转错误</span></strong></span><br  /></p><p><span>参考#46处理。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">48. MOTION ERROR：SAMPLE MIXER UP/DOWN</p></section></section></section><p><span><strong><span>运动错误：样品搅拌器上下运动错误</span></strong></span><br  /></p><p><span>参考#46处理。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">49. MOTION ERROR：SAMPLE PROBE AIR STRIP</p></section></section></section><p><span><strong><span>运动错误：样品针气体冲洗错误</span></strong></span><br  /></p><p><span>a)检查5A电磁阀是否正常。<br  />b)按“HOME”复位，观察运动情况。<br  />c)执行“SAMPLE AIR STRIP TEST”诊断测试(3.8.3.2)。<br  />d)请联系当地维修站。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">50. MOTION ERROR：SAMPLE PROBE ROTATE</p></section></section></section><p><span><strong><span>运动错误：样品针左右移动错误</span></strong></span><br  /></p><p><span>a)参考#40处理。<br  />b)执行“SAMPLE PROBE ROTATE ALIGNMENT”诊断调节(3.5.2)。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">51. MOTION ERROR：SAMPLE PROBE UP/DOWN</p></section></section></section><p><span><strong><span>运动错误：样品针上下运动错误</span></strong></span><br  /></p><p><span>参考#50处理。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">52. MOTION ERROR：SAMPLE PROBE WASH</p></section></section></section><p><span><strong><span>运动错误：样品针冲洗错误</span></strong></span><br  /></p><p><span>a)冲洗样品针内外部，观察工作情况。<br  />b)执行“EXTERNAL PROBE WASH TEST”诊断测试(3.8.2)。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">53. MOTION ERROR：SAMPLE PUMP</p></section></section></section><p><span><strong><span>运动错误：样品注射器泵运动错误</span></strong></span><br  /></p><p><span>a)参考#43处理。<br  />b)执行“SAMPLE SYRINGE PUMP ALIGNMENT”诊断调节(3.5.11)。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">54. MOTION ERROR：SAMPLE VALVE</p></section></section></section><p><span><strong><span>运动错误：样品注射器阀运动错误</span></strong></span><br  /></p><p><span>a)参考#44处理。<br  />b)执行“SAMPLE SYRINGE VALVE ”诊断测试(3.8.2.4)。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">55. MOTION ERROR：SUMP PUMP</p></section></section></section><p><span><strong><span>运动错误：废液泵错误</span></strong></span><br  /></p><p><span>a)冲洗排废系统，观察废液泵工作情况。<br  />b)执行“SUMP PUMP TEST”诊断测试(3.8.4)。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">56. MOTION ERROR：VACUUM RESERVOIR</p></section></section></section><p><span><strong><span>运动错误：真空缓冲罐错误</span></strong></span><br  /></p><p><span>a)检查真空缓冲罐是否积存了液体。<br  />b)检查相关管路是否漏气，单向阀是否正常。<br  />c)冲洗排废系统，观察废液泵工作情况。<br  />d)执行“COMPRESSOR/VACUUM PUMP TEST”诊断测试(3.8.3)。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">57. MOTION ERROR：WASH MIXER VALVE</p></section></section></section><p><span><strong><span>运动错误：稀释冲洗混合电磁阀错误</span></strong></span><br  /></p><p><span>a)冲洗灌满稀释冲洗瓶，观察工作情况。<br  />b)执行“MIX WASH SOLUTION TEST”诊断测试(3.8.2)。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">58. MOTION ERROR：WASH TO CUVETTE WASH</p></section></section></section><p><span><strong><span>运动错误：冲洗液冲洗反应杯时错误</span></strong></span><br  /></p><p><span>参考#22处理。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">59. MOTION ERROR：MOTION SYSTEM REQUIRES HOMING</p></section></section></section><p><span><strong><span>运动错误：运动部件须复位</span></strong></span><br  /></p><p><span>a)按“STOP”后未复位，按“HOME”复位即可。<br  />b)非正常中断运行后未复位，按“HOME”复位即可。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">60. MSC WAS DEAD AT INITIALIZATION</p></section></section></section><p><span><strong><span>MSC 驱动板初始化没有响应</span></strong></span><br  /></p><p><span>a)仪器“IDLE”后，重新启动仪器。<br  />b)执行“MOTOR SYSTEM CONTROLER”诊断测试(3.2.3)。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">61. PELTIER FAILURE</p></section></section></section><p><span><strong><span>冰箱半导体制冷器故障</span></strong></span><br  /></p><p><span>a)仪器“IDLE”后，重新启动仪器。<br  />b)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">62. POWER SUPPLY FAILURE：CX4</p></section></section></section><p><span><strong><span>CX4部分电源组件故障</span></strong></span><br  /></p><p><span>a)检查仪器电源状态指示灯情况。<br  />b)请联系当地维修站。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">63. REAGENT LEVEL SENSE ERROR .CHECK REAGENT STATUS SCREEN&nbsp;FOR LOCATION.</p></section></section></section><p><span><strong><span>试剂液面检测错误，根据显示检查试剂状态</span></strong></span><br  /></p><p><span>a)检查试剂瓶相应A B C 孔是否有气泡。试剂量是否正常。<br  />b)检查试剂架是否装载正确。<br  />c)执行“PROBE HEIGHT ADJUSTMENT”诊断调节(3.6.10)。<br  />d)检查液面感应线是否导通。<br  />e)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">64. REAGENT NOT DETECTED AT SAMPLE INJECT</p></section></section></section><p><span><strong><span>在加样品时没有检测到反应杯内试剂</span></strong></span><br  /></p><p><span>a)检查反应杯是否有破碎。<br  />b)检查试剂架是否有气泡。<br  />c)检查气泡发生器是否工作正常。试剂针管路是否有气泡。<br  />d)检查样品针液面感应线是否正常。<br  />e)执行“BUBBLE GENERATOR”诊断测试(3.8.2.4)。<br  />f)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">65. SAMPLE NOT DETECTED</p></section></section></section><p><span><strong><span>没有检测到样品</span></strong></span><br  /></p><p><span>a)检查样品是否足够。<br  />b)检查样品感应线是否正常。<br  />c)执行“SAMPLE SYSTEM LEVEL SENSE TEST”诊断测试(3.5.2)。<br  />d)执行“SAMPLE PROBE HEIGHT ADJUSTMENT”诊断调节(3.5.2)。<br  />e)请联系当地维修站。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">66. SOFTWARE ERROR DETECTED</p></section></section></section><p><span><strong><span>检测到软件错误</span></strong></span><br  /></p><p><span>a)仪器“IDLE”后，重新启动仪器。<br  />b)重新安装软件，并装回备份参数。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">67. STAT LOAD WAS REQUESTED，BUT NO SECTOR WAS LOADED</p></section></section></section><p><span><strong><span>按了“STAT LOAD”键，但没有样品架被加载</span></strong></span><br  /></p><p><span>参考#16处理。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">68. TEMPERATURE CONTROL FAILURE</p></section></section></section><p><span><strong><span>温度控制错误</span></strong></span><br  /></p><p><span>a)仪器刚启动时，未达到规定的温度范围。<br  />b)室温太高，仪器不能有效控制。<br  />c)冰箱制冷器老化或太脏，制冷效率下降。<br  />d)执行“TEMPERATURE CONTROL TEST”诊断测试(3.4)。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">69. VACUUM LIQUID TRAP TOO HIGH</p></section></section></section><p><span><strong><span>真空缓冲瓶液面太高</span></strong></span><br  /></p><p><span>a)参考#56处理。<br  />b)执行诊断测试(3.8.4.1 和3.8.4.2)。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">70. VACUUM PRESSURE TOO LOW</p></section></section></section><p><span><strong><span>真空压力太低</span></strong></span><br  /></p><p><span>a)检查真空管路，瓶盖等是否漏气或破损，单向阀和过滤器是否堵塞或穿&nbsp;<br  />漏等。<br  />b)压缩机活塞老化。<br  />c)请联系当地维修站。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">71. WASH CONCENTRATE AND/OR PROBE RINGE SOLUTION IS LOW</p></section></section></section><p><span><strong><span>浓缩冲洗液和/或针头清洗液太少</span></strong></span><br  /></p><p><span>a)检查浓缩清洗液和针头清洗液是否足够。<br  />b)检查浮子感应及连接是否正常。<br  />c)执行诊断测试(3.8)。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">72. WASTE BUCKET FULL</p></section></section></section><p><span><strong><span>废液灌充满</span></strong></span><br  /></p><p><span>a)冲洗排废系统，观察废液泵工作情况。<br  />b)检查清洁所有废液管路。<br  />c)执行诊断测试(3.8)。</span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">73. WATER PRESSURE SENSOR FAILURE</p></section></section></section><p><span><strong><span>水压传感器错误</span></strong></span><br  /></p><p><span>a)检查离子水供应系统是否正常。<br  />b)检查传感器连接是否正常。<br  />c)检查调节阀是否正常。<br  />d)请联系当地维修站。<br  /></span></p><p><br  /></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">74. WATER PRESSURE TOO HIGH / LOW</p></section></section></section><p><span><strong><span>水压太高或太低</span></strong></span><br  /></p><p><span>a)检查水压表是否指示正常。<br  />b)检查离子水供应系统是否正常，供水开关是否打开。<br  />c)检查系统是否漏气。<br  />d)检查进水阀，浮子传感器及连接是否正常。<br  />e)检查压力传感器是否正常。<br  />f)请联系当地维修站。<br  /><br  /></span></p><section data-tools="gulangu" data-id="89175"><section><section><p data-brushtype="text">75．REAGENT NOT ON BOARD</p></section></section></section><p><span><strong><span>已编程但未装载该项试剂</span></strong></span><br  /></p><p><br  /></p></section><p><br  /></p><section data-role="paragraph"><p><br  /></p></section><section><p><br  /></p><p><span><strong><span>【版权声明】：</span><span>本文由整理发布，资料源自网络，版权归原作者所有，转载请注明来源！</span></strong><br  /><br  /></span></p><section><p><img src="image/20200927/ffa6781c03117c1225d40fca86b93339_3.jpg" /></p><span><strong>微信ID：yxiubang</strong></span></section><section><span><strong><p><img src="image/20200927/3d50c8c9238d63bc2f0cee8c97c8bf3a_4.jpg" /></p>长按左侧二维码关注</strong></span></section><p><br  /></p><p><br  /></p></section></section><p><br  /></p>