Discuz! Board

 找回密码
 立即注册
搜索
热搜: 活动 交友 discuz
查看: 6|回复: 0

SYSMEX仪器使用注意事项及故障解答

[复制链接]

1万

主题

1万

帖子

5万

积分

管理员

Rank: 9Rank: 9Rank: 9

积分
58026
发表于 2020-9-27 08:50:10 | 显示全部楼层 |阅读模式

                    

                    

                    
                    
                    <section data-role="outer" label="Powered by gulangu"><section><p><p><img src="image/20200927/75fa950ca5fd779d2fe6a9f65b2dcece_1.png" /></p></p></section><section data-color="rgb(235, 103, 148)"><p><p><img src="image/20200927/9856aea3f23621f86c52bba4920c9ead_2.jpg" /></p></p></section><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)" data-custom="rgb(235, 103, 148)"><section><section></section><p><span>1</span></p><section><p><span>当仪器出现问题时,千万不要在短时间内反复开关电源,至少要间隔60秒钟以上,否则极容易损坏CPU板</span><span>(此类事例已经发生过数起)</span></p></section></section></section><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)" data-custom="rgb(235, 103, 148)"><section><section></section><p><span>2</span></p><section><p>仪器的分析结果有异常时,如何判断是否是仪器故障引起的?</p><p><br  /></p><p>使用原厂质控。如果质控做出的结果是正常的话,仪器故障的可能性很小。在这种情况下,标本的采集,使用的采血管,或者是标本本身有问题的可能性比较大。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>3</span></p><section><p>XE2100在使用自动进样方式时应注意:</p><p><br  /></p><p>真空采血管盖帽必须盖牢,不然会引起穿刺针的偏移,这极有可能导致穿刺针在穿刺过程中其针尖扎中试管壁,而造成穿刺针的损坏。条形码必须平整,没有皱褶及破损,否则会使试管夹持不牢而引起机械故障。如果不想使用条码阅读器,则在电脑中选择菜单画面,通过“ID reader setting”将条码阅读器的动作撤销。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>4</span></p><section><p>XE2100更换试剂时应该注意:</p><p><br  /></p><p>如果是NRBC或者RET试剂(包括染液和稀释液),则必须同时更换染液和稀释液,否则由于没有用于检测NRBC及RET稀释液的传感器,仪器将无法知道稀释液瓶内的试剂是否用完,这样,可能会使空气进入到标本内。试剂用完与否是通过上一次更换试剂后计数器的计数值来检测的。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>5</span></p><section><p>XE2100仪器,当标本分析完成后,每天必须使用Cellclean清洁液执行SHUTDOWN关机保养程序。</p><p><br  /></p><p>由于激光分析通道非常狭窄,如果不执行SHUTDOWN关机保养程序,会导致激光分析通道发生堵塞,这会引起灵敏度的变化而使得假阳性率或假阴性率升高,甚至需要工程师重新调整激光系统,使机器在一段时间内不能使用。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>6</span></p><section><p>POCH100i在做质控时,RBC、HGB是正常范围内,但是MCHC总是偏高。</p><p><br  /></p><p>由于MCHC=HGB/HCT的计算值,所以可以通过调整HCT来调整MCHC。但是如果不是用SYSMEX的质控,用临检中心或其他的质控来做的话,MCHC不正常是可能的。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>7</span></p><section><p>仪器报警正压或负压错误。</p><p><br  /></p><p>可能原因:压力调节不当,压缩机产生的压力不足,气路管道或接口处漏气。</p><p><br  /></p><p>解决方法:调节正压或负压,检查压缩机的电源是否接通,检查气路管道的连接口有无松动。如果还无法修复,请尽快联系SYSMEX经销商工程师。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>8</span></p><section><p>仪器报警为进样器运行方面的错误。</p><p><br  /></p><p>请清洁进样器上的灰尘及污物,尽量保证进样器上的传感器的干净清洁。也可能是传感器位置不当引起,需要工程师进行调整。仪器报激光电源错误(XT1800i或XT2000i)再进行一次标本分析,如果错误信息仍然出现,则要和SYSMEX经销商工程师联系。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>9</span></p><section><p>KX-21N在做标本时常出现“WL”的报警。</p><p><br  /></p><p>由于存储试剂不当引起的,试剂温度太低。将稀释液在室温下放置一段时间再使用。试剂的保存条件一般为5—30℃。仪器使用的外界环境温度范围在15-30℃,最佳温度在25℃左右。</p></section></section></section><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>10</span></p><section><p>UF100仪器,手动、自动进样方式做标本,结果都偏低,有时为零。</p><p><br  /></p><p>可能是吸样管路(如样本过滤器、SRV、FLOWCELL等)堵塞,清洗相应部位即可,也有可能是光学系统偏移,需要由工程师使用激光调整颗粒进行确认。</p></section></section></section><p><br  /></p><p><br  /></p><section data-tools="gulangu" data-id="89413" data-color="rgb(235, 103, 148)"><section><section></section><p><span>11</span></p><section><p>UF50仪器,错误信息为“鞘液温度高”。</p><p><br  /></p><p>由于仪器周围排气通风不好,导致仪器内部温度过高。调整仪器位置,清洗排风扇。UF100仪器,错误信息是“Background error”,Total值偏高,做样本时值偏高。Flowcell较脏,用Cellclean反复清洗管路和Flowcell并且调整仪器的灵敏度。</p></section></section></section><p><br  /></p><p><br  /></p><section><p><span><strong><span>【版权声明】:</span><span>本文由整理发布,资料源自网络,版权归原作者所有,转载请注明来源!</span></strong><br  /><br  /></span></p><section><p><img src="image/20200927/a05d8baa72c8998dc887d8b4a4cf8e2d_3.jpg" /></p><span><strong>微信ID:yxiubang</strong></span></section><section><span><strong><p><img src="image/20200927/3d50c8c9238d63bc2f0cee8c97c8bf3a_4.jpg" /></p>长按左侧二维码关注</strong></span></section><p><br  /></p><p><br  /></p></section></section><p><br  /></p>
               
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

Archiver|手机版|小黑屋|Comsenz Inc. ( 浙ICP备17000336号-1 )

GMT+8, 2025-3-15 04:18 , Processed in 0.074430 second(s), 33 queries .

Powered by Discuz! X3.4

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表