西门子移动式X线机重装系统教程（型号orbic 3D）

admin

                    

                    

                    
                    
                    <section><section powered-by="gulangu"><section><section><p><img src="image/20201019/d6e89edf6139ad8643ba162be5e9a663_1.gif" /></p></section></section></section><section powered-by="gulangu"><section><section><p>清楚数据包</p></section> <p><img src="image/20201019/237ff723e23881a3d146532f7bfe985e_2.png" /></p> <section></section></section></section><section powered-by="gulangu"><section><section><p>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;首先进入维修模式，选择“utilties”，选择“database”，选择“DB remove 1”；选择“go”；最后重启。<br  /></p></section></section></section><section powered-by="gulangu"><section><section><p>重刷BIOS</p></section> <p><img src="image/20201019/237ff723e23881a3d146532f7bfe985e_2.png" /></p> <section></section></section></section><section powered-by="gulangu"><section><section><p>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;开启工作站同时按“F2”，输入密码“pwd4sp”，按“F9”（恢复默认设置），设定时间。</p><p>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;选择“Adavaned s c of”，在选择</p><p>&nbsp; &nbsp; &nbsp; &nbsp; “sata0 cornpatiable model”设置为“disabled”</p><p>&nbsp; &nbsp; &nbsp; &nbsp; “sata Rbid enable”设置为“disabled”</p><p>&nbsp; &nbsp; &nbsp; &nbsp; “sata ahci&nbsp; enable”设置为“disabled”</p><p>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;按“F10”（<span>保存</span><span>）</span></p><p><span>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;再次重启开机，按“F2”，选择“boot”，选择“satacd”（光盘启动），放入“</span><span>sp m460 bios cd</span><span>”光盘，按“F10”，保存启动。</span></p><p><span>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;等待光盘运行，“installation done”、“please remove cd”、“please turn off or reset system”等，运行完毕后退盘。</span></p><p><span>&nbsp; &nbsp; &nbsp; &nbsp; &nbsp;按“ctrl+alt+delete”重启后完成。</span></p></section></section></section><section powered-by="gulangu"><section><section><p>重装系统</p></section> <p><img src="image/20201019/237ff723e23881a3d146532f7bfe985e_2.png" /></p> <section></section></section></section><section powered-by="gulangu"><section><section><p>&nbsp; &nbsp; &nbsp; &nbsp; 重启系统后，先装引导盘，放入光盘（cobr），选择“restone the system”，选择“ok”，等到“recorely image and dick ok<span>”。</span></p><p><span>&nbsp; &nbsp; &nbsp; &nbsp; 装系统盘（recovery 1 2），第一次登入：administrator，adm$pwd$4$med，导入新的设置，首先把设置放入D盘，进入维修模式：“backup”，选择“restore”，选择“D：”</span></p><p><span>&nbsp; &nbsp; &nbsp; &nbsp;选择新的设置“sw setting”、“aspi asetting”、“3d setting”、“exam set”，按“shift”，按“go”，重启完成。</span></p></section></section></section><section powered-by="gulangu"><section><section><p><br  /></p></section></section></section><section powered-by="gulangu"><section><section> <section powered-by="gulangu"><section><section><p>欢</p></section></section></section> </section><section> <section powered-by="gulangu"><section><section><p>迎</p></section></section></section> </section><section> <section powered-by="gulangu"><section><section><p>关</p></section></section></section> </section><section> <section powered-by="gulangu"><section><section><p>注</p></section></section></section> </section></section></section><section powered-by="gulangu"><section><section><p><br  /></p></section></section></section><section powered-by="gulangu"><section><section> <section powered-by="gulangu"><section><section><p><img src="image/20201019/7856584fda94ba1983014b524dead643_5.jpg" /></p></section></section></section> </section><section> <section powered-by="gulangu"><section><section> </section></section></section> </section><section> <section powered-by="gulangu"><section><section><p>关注我们</p><p>一起涨姿势！</p></section></section></section> </section></section></section></section>