<p><span><span><br /></span></span></p><p><span><span></span></span></p><p><p><img src="image/20201019/1bd08b695d5fd805cb63ee05a2610294_1.jpg" /></p></p><p><span><span>医院关机后重启无法进入系统，报错启动时无法时无法确认系统性能。请关闭后再打开控制电源。</span></span><br /></p><p><br /></p><p><span><span>重新启动后依然无法进入系统，打开</span>shell输入su - 密码#bigguy获取root权限，reconfig做原始数据盘格式化database， 报错失败，让关机断电重做reconfig。</span></p><p><span><span>更换</span>2个原始数据盘后，做磁盘阵列重建，可以检测磁盘的好坏，容量，读写速度</span></p><p><span><span>一、重建</span>raid阵列</span><span> Create (-c) Script</span></p><table cellspacing="0" width="554"><tbody><tr><td width="60" valign="center" rowspan="4"><br /></td><td width="494" valign="center"><br /></td></tr><tr><td width="494" valign="center"><p><strong><span>The sudo gre-raid -c (create) script erases all data on the Scan Disk. Patient information WILL be lost. Make certain to back-up all patient data prior to performing this test.</span></strong></p></td></tr><tr><td width="494" valign="center"><br /></td></tr><tr><td width="494" valign="center"><br /></td></tr></tbody></table><p><span>With Application Software down, open a Unix Shell and type the following:</span></p><p><span>{ctuser@</span><em><span>hostname</span></em><span>}</span><strong><span> rsh darc</span></strong></p><p><span>[ctuser@darc ~]$</span><strong><span> sudo gre-raid -c</span></strong></p><p><span>************************** Warning ******************************</span><span>* If a new disk array is created, all scan data on the current *</span><span>* disk array will be lost. *</span><span>*****************************************************************</span><span> </span></p><p><span>Are you sure you want to create a new disk array (yes/no)?</span><strong><span> yes</span></strong></p><p><strong><span>Table 1: </span></strong><span>Example Create Command Output</span></p><table cellspacing="0" width="556"><tbody><tr><td width="556" valign="center"><p><span>{ctuser@hostname}[1] rsh darc</span><span>Last login: Mon Jul 24 17:03:43 from oc</span><span>[ctuser@darc ~]$ sudo gre-raid -c</span><span>gre-raid: built Jun 22 2006 20:34:02</span><span> </span></p><p><span>/dev/sd<x>: scanning disk array...</span><strong><span>done</span></strong></p><p><span>Device Bus ID Mfg Model Fwrev Serial-number</span><span>/dev/sda 0 0 SEAGATE ST336754LW 0003 3KQ1H79N00007634SPRT</span><span>/dev/sdb 0 1 SEAGATE ST336754LW 0003 3KQ1JP5300007634RNN5</span><span> </span><span>Adaptec driver not found. Continuing...</span><span>dasType: non-VDAS</span><span>/usr/g/config/gre-raid-2.cfg: RAID-0 profile</span></p><p><span>/raw_data: unmounting filesystem...</span><strong><span>done</span></strong></p><p><span>/dev/md0: stopping...</span><strong><span>done</span></strong></p><p><span>/var/log/messages: checking for SCSI errors...done</span><span>************************** Warning ******************************</span><span>* If a new disk array is created, all scan data on the current *</span><span>* disk array will be lost. *</span><span>*****************************************************************</span><span>Are you sure you want to create a new disk array (yes/no)? yes</span><span> </span><span>/var/log/messages: 0 drive(s) found with SCSI errors found since last start</span><span> </span></p><p><span>/dev/sda: testing...drive_spec...52.0MB/sec...</span><strong><span>done</span></strong></p><p><span>/dev/sdb: testing...drive_spec...51.9MB/sec...</span><strong><span>done</span></strong></p><p><span> </span></p><p><span>/dev/sda: partitioning...</span><strong><span>done</span></strong></p><p><span>/dev/sdb: partitioning...</span><strong><span>done</span></strong></p><p><span>/dev/md0: creating disk array...</span><strong><span>done</span></strong></p><p><span>/dev/md0: RAID-0 active with </span><strong><span>(2) drives</span></strong><span>, 256k chunk size, and 69GB capacity</span></p><p><span>/dev/md0: creating filesystem...</span><strong><span>done</span></strong></p><p><span>/raw_data: mounting /dev/md0 filesystem...</span><strong><span>done</span></strong></p><p><span> </span></p><p><span>/raw_data: testing...170.1MB/sec...</span><strong><span>done</span></strong></p><p><span>/raw_data: 0.0% used, 68.2GB avail</span></p><p><span> </span></p><p><strong><span>gre-raid: success</span></strong></p><p><span>[ctuser@darc ~]$</span></p></td></tr></tbody></table><p><span>Verify the create partitions diagnostic passes and all output looks good.</span></p><p><span>erform the assemble and query commands if the create has been successful.</span></p><p><span><span>如果硬盘有问题，会在</span>testing disk 的时候报错。</span></p><p><span><span>二、</span>darc系统的安装方法（大约需要半个小时）</span></p><p><span>darc的系统程序是包含在OS这张光盘里面的，安装darc系统首先要修改darc主板的Bios设置</span></p><p><br /></p><p><span> 然后在打开的shell 窗口里面会显示darc主板的Bios设置信息，根据darc 的类型，分为</span><strong><span>Westville</span></strong><strong><span><span>和</span></span></strong><strong><span>Jarrell</span></strong><strong><span><span>，设置情况如下</span></span></strong></p><p><strong><span> (For Westville) </span></strong><span> Verify the Boot device Priority is set to:</span></p><p><span> IBA 1.1.08 Slot 0338</span></p><p><span> ATAPI CD-ROM</span></p><p><span> Hard Drive</span></p><p><span> IBA 1.1.08 Slot 0339</span></p><p><span> Removable Devices</span></p><p><strong><span>(For Jarrell) </span></strong><span>Verify the Boot device Priority is set to:</span></p><p><span>IBA GE slot 0320v</span></p><p><span> S -slimtype COMBO</span></p><p><span>M-ST94813A</span></p><p><span>·</span><span> </span><span>IBA GE slot 0321v</span></p><p><span>·</span><span> </span><span>EFI Boot Manager</span></p><p><span>·</span><span> </span><span><span>在</span>pc 的光驱里面安装darc系统</span></p><p><span>·</span><span> </span><span>·</span><span> </span><span>·</span><span> </span><span>Open a Unix Shell and type the following:</span></p><p><span>·</span><span> </span></p><p><span>{ctuser@hostname}</span><strong><span>su -</span></strong></p><p><span> </span></p><p><span> </span></p><p><span>assword:</span><strong><span>#bigguy</span></strong></p><p><span> </span></p><p><span> </span></p><p><span>[root@hostname]</span><strong><span>cd /usr/g/scripts</span></strong></p><p><span> </span></p><p><span> </span></p><p><span>[root@hostname]</span><strong><span> ./load_darc_subsystem</span></strong></p><p><span> </span></p><p><span>An Attention window appears. See the illustration below.</span></p><p><br /></p><p><span>·</span><span> </span><span>Follow the instructions in the Attention window.</span></p><p><span>·</span><span> </span><span>·</span><span> </span><span>Select [OK] .</span></p><p><span>·</span><span> </span><span>·</span><span> </span><span>The Unix Shell will display output during the DARC load (approximately 33 minutes). Example output is as follows:</span></p><p><span>·</span><span> </span><span>[root@hostname</span><em><span>scripts]# ./load_darc_subsystem</span></em></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [Start time] Loading the darc subsystem(OS + Apps) takes 30 minutes</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [Start time] Loading the darc OS</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [Time] Loading the darc OS is complete</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [Time] Loading the darc apps</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [End time] Loading the darc is complete</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [End time] Load started: (Date) (Start time)</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [End time] Load ended: (Date) (End time)</span></p><p><span>·</span><span> </span><span>[load_darc_subsystem] [End time] Finished loading darc subsystem.</span></p><p><span>·</span><span> </span><span>[root@</span><em><span>hostname]#</span></em></p><p><span>·</span><span> </span><span><span>成功后，</span>shell窗口会自动关闭。darc系统装完后，需要把Bios设置还原为以前的设置。</span></p><p><span>·</span><span> </span><span><span>三、安装</span>S-O-l</span></p><p><span>·</span><span> </span><span><span>把</span>darc接上显示器，将Bios设置中光驱启动CD-rom设置为第一启动项，把S-o-l这张盘放入光驱中，会自动安装，大约2-3分钟，安装完后darc重新启动，光驱弹出，说明s-o-l安装成功，然后把biso恢复设置。</span></p><p><span></span></p><p><p><img src="image/20201019/3dfd13f42c8d3306fb3b352e9ed7cd2b_2.jpg" /></p></p><p><span></span><br /></p><p><br /></p><p><br /></p><p><p><img src="image/20201019/7822a4e2249e86a45760fbbfc1675e38_3.gif" /></p></p><p><span> </span></p><p><span> </span></p><p><span> </span></p><p><br /></p>
发表于 2020-10-19 09:17:21
erform the assemble and query commands if the create has been successful.</span></p><p><span><span>如果硬盘有问题，会在</span>testing disk 的时候报错。</span></p><p><span><span>二、</span>darc系统的安装方法（大约需要半个小时）</span></p><p><span>darc的系统程序是包含在OS这张光盘里面的，安装darc系统首先要修改darc主板的Bios设置</span></p><p><br /></p><p><span> 然后在打开的shell 窗口里面会显示darc主板的Bios设置信息，根据darc 的类型，分为</span><strong><span>Westville</span></strong><strong><span><span>和</span></span></strong><strong><span>Jarrell</span></strong><strong><span><span>，设置情况如下</span></span></strong></p><p><strong><span> (For Westville) </span></strong><span> Verify the Boot device Priority is set to:</span></p><p><span> IBA 1.1.08 Slot 0338</span></p><p><span> ATAPI CD-ROM</span></p><p><span> Hard Drive</span></p><p><span> IBA 1.1.08 Slot 0339</span></p><p><span> Removable Devices</span></p><p><strong><span>(For Jarrell) </span></strong><span>Verify the Boot device Priority is set to:</span></p><p><span>IBA GE slot 0320v</span></p><p><span>